Door Handle Backset: 60mm vs 70mm, and How to Measure It

Matte black lever door handle on a white internal door in a modern Australian hallway

Quick answer: the backset is the distance from the edge of the door to the centre of the handle or keyhole. Most modern internal doors in Australia use a 60mm backset, and 70mm is the other common size. Narrow doors, like French doors and glass-panel doors, often need a shorter 44 to 46mm backset. If you're replacing a handle, measure your existing one and match it.

That's the short version. The rest of this guide walks you through measuring it properly, what to check alongside it, and the mistakes that most often lead to ordering the wrong handle.

What is a backset?

The backset is measured on the face of the door, from the outside edge (the edge with the latch) to the centre of the hole where the handle spindle or lock cylinder goes through. It's set by the latch or lock inside the door, not by the handle itself. That's why two handles that look the same can sit in different spots on the door.

Diagram showing how to measure a door backset: 60mm or 70mm on a standard internal door, and 44 to 46mm on a narrow French door stile

Get it wrong and the new handle won't line up with the latch. You'll either be drilling new holes or sending the order back.

How to measure your backset

Measuring a door backset with a tape measure from the door edge to the centre of the handle hole
  1. Open the door so you can see the edge with the latch.
  2. Find the centre of the handle hole. If the handle is on, measure to the centre of the spindle (the square bar the handle turns on). If it's off, measure to the centre of the large round hole in the door face.
  3. Measure from the door edge straight across to that centre point. Don't measure to the edge of the hole.
  4. Round to the nearest standard size. You'll almost always land on roughly 45mm, 60mm or 70mm.

For a keyed lock or deadbolt, measure to the centre of the keyhole or cylinder instead.

60mm vs 70mm: which do you need?

60mm is the most common backset on modern internal doors, and it's what most passage and privacy sets are set up for out of the box.

70mm moves the handle further in from the edge. You'll see it on some entrance sets and doors where the handle needs a bit more clearance from the frame.

The good news: many tubular latches sold in Australia are adjustable between 60mm and 70mm, so one latch covers both. Check the product specs for "adjustable latch" before ordering. Our Adjustable 60–70mm Passage Latch is a good example, and there's an Entrance version for keyed sets. If it's not adjustable, buy the size that matches your door.

Stainless steel tubular door latch with bevelled latch bolt and strike plate

When to use a shorter backset (44 to 46mm)

French doors, double doors, glass-panel doors and some older panelled doors have a narrow vertical timber section (the stile) where the handle sits. A 60mm backset would put the handle too far in, sometimes right over the glass.

Brushed brass lever handle on a backplate, centred on the narrow stile of a white French door

The fix is to measure the width of the stile, halve it, and choose the backset closest to that number. A 92mm stile, for example, gives you 46mm, so a 44 to 46mm latch is the right pick. That keeps the handle centred on the timber, which looks right and feels better to use.

For a standard handle on a narrow stile, a 45mm latch like the IVER Split Cam Tube Latch does the job.

Mortice locks are different

Mortice locks sit in a pocket cut into the door edge, and their backsets vary more than standard latches. Sizes like 46mm and 57mm are common, along with 60mm. If you're replacing a mortice lock, measure the old one carefully and check it against the specs. Our mortice locks list the backset in the product name where it matters. For French and double doors, where the door edges overlap, choose a rebated lock such as the IVER Rebated 85mm Euro Mortice Lock with a 45mm backset.

Other measurements to check at the same time

Door thickness

Most internal hollow-core doors in Australia are around 35mm thick, while external doors are usually thicker, often 40mm or more. Handles, latches, privacy sets and deadbolts all list a door thickness range, so measure across the edge of the door and make sure yours falls inside it.

The face hole

Most modern handle sets need a 54mm hole through the face of the door. If your door has a smaller hole from older hardware, it may need to be opened up.

The rose or backplate

If you're replacing old handles, measure the old rose or backplate as well. The new one needs to cover any marks, screw holes or paint lines left behind. Square roses and backplates are handy for hiding old damage.

Backset at a glance

Door Typical backset What to do
Modern internal door (flat or hollow-core) 60mm Standard passage or privacy set, or an adjustable 60/70mm latch
Entrance door 60mm or 70mm Check the entrance set specs, and match your existing lock
French, double or glass-panel door 44 to 46mm Measure the stile, halve it, pick the closest size
Older panelled door Varies Measure the stile and the existing hole
Mortice lock Varies (often 46 to 60mm) Measure the old lock and match it exactly
Replacing any existing handle Whatever you have now Match it, so the holes line up

Common backset mistakes

  • Measuring to the edge of the hole instead of the centre. It throws the number out by 25mm or more.
  • Assuming every door is 60mm. It's the most common size, not the only one. French doors and older homes are where this catches people out.
  • Changing the backset on an existing door without planning the repair. The old hole will need filling and the door repainting.
  • Forgetting the door thickness. A handle can match the backset and still not fit a thick external door.
  • Mixing latches and handles from different brands without checking they're compatible. Standard tubular latches are fairly interchangeable, but some designs need their own latch.

Products mentioned in this guide

Ready to choose your handles?

Once you know your backset, browse our door handles and knobs by style and finish, or go straight to door lock sets for front and back doors. If you just need a new latch or privacy turn, you'll find them in lock accessories.

Still not sure? Email a photo of your door edge and your measurement to customer.service@ayvan.com.au, or call us on 03 9017 0217. The advice is free, and you're welcome to visit our showroom at 169 Para Road, Greensborough. Most orders arrive in 2 to 5 business days, and shipping is free over $250.

Frequently asked questions

What is the standard door handle backset in Australia?

60mm is the most common backset on modern internal doors in Australia. 70mm is the other common size, and many latches adjust between the two. French doors and narrow stile doors often use 44 to 46mm.

How do I measure the backset on my door?

Measure from the edge of the door to the centre of the handle spindle or the centre of the hole in the door face. Don't measure to the edge of the hole. The result is usually close to 45mm, 60mm or 70mm.

Can I use a 70mm latch on a 60mm door?

Not without drilling a new hole. If your latch is adjustable between 60mm and 70mm, you can simply set it to 60mm. Otherwise, buy a latch that matches the backset already on your door.

What backset do French doors use?

French doors usually have a narrow stile, so they often need a 44 to 46mm backset. Measure the width of the stile, halve it, and choose the backset closest to that number.

Does the backset affect which door handle I can buy?

The backset is set by the latch, not the handle, so most handles work with either 60mm or 70mm latches. Check that the handle set includes a latch in your size, or buy a compatible latch separately.

What thickness are internal doors in Australia?

Most internal hollow-core doors are around 35mm thick, and external doors are usually thicker, often 40mm or more. Check the door thickness range listed on any handle or lock before ordering.